These unconventional pumpkin carving designs will ensure you have the spookiest Halloween ever.
The post 5 Tutorials for Next Level Pumpkin Carving appeared first on Make: DIY Projects, How-Tos, Electronics, Crafts and Ideas for Makers.
Thursday, October 1
5 Tutorials for Next Level Pumpkin Carving
Well before Super Bowl comes to California, host city bans drones over stadiums
Levi's Stadium crowd on August 17, 2014. (credit: Jim Bahn)
Kickoff for Super Bowl 50 is not scheduled until February 7, 2016, but Santa Clara is getting ready now. The city has a new local law imposing a half-mile “no-fly zone” over Levi’s Stadium (home of the San Francisco 49ers), the Santa Clara University stadium, and “within or over any sporting and/or large venue special event.”
The ordinance, which took effect on September 19 and was first reported by Government Technology, stipulates that violation of the law would be treated as a misdemeanor. However, the law also notes that the drone in question could be confiscated by local authorities. Earlier this month, a man was arrested near the US Open tennis tournament in New York City after a drone crashed into the stands.
This Silicon Valley city’s law is on top of an existing 2014 Notice to Airmen (NOTAM) No. FDC 4/3621, which marked the first time US flight regulators have moved to criminally punish wayward drone pilots.
Read 5 remaining paragraphs | Comments
Because Burning Man Needed More LEDs
There are a lot of blinky glowy things at Burning Man every year, and [Mark] decided he would literally throw his hat into the ring. He built a high visibility top hat studded with more RGB LEDs than common sense would dictate. It’s a flashy hat, and a very good example of the fashion statement a few hundred LEDs can make.
[Mark]’s top hat has 481 WS2812b addressable LEDs studded around the perimeter, a common LED choice for bright and blinky wearables. These LEDs are driven by a Teensy 3.1, with a Bluetooth transceiver, a GPS module, a compass, and gyro/accelerometer attached to the microcontroller. That’s a lot of hardware, but it gives [Mark] the capability of having the hat react to its own orientation, point itself North, and allow for control via a modified Nintendo NES controller.
The WS2812 LEDs draw a lot of power, and for any wearable project having portable power is a chief concern. [Mark]’s original plan was to use an 8x battery holder for the electronics enclosure, and use five AA batteries to power the hat. The total idle draw of the LEDs was 4.5 Watts, and with even a few LEDs blinking colors there was a significant voltage drop. The idea of powering the hat with AA batteries was discarded and the power source was changed to a 195 Watt-hour lithium ion battery bank that was topped off each day with a solar panel.
The hat is awesome, exceedingly bright, and something that gets a lot of attention everywhere it goes. For indoor use, it might be too bright, but this could be fixed with the addition of a bit of black stretchy fabric, like what our own [Mike Szczys] did for his DEF CON hat. [Mark]’s hat is just version 1, and he plans on making a second LED hat for next year.
Filed under: led hacks, wearable hacks
This PCB Business Card is Logically Different
Having seen a number of PCB business cards [Will] decided to go against the more popular choice of a micro-controller based design and show some character with a logic based finite state machine. [Will] uses a single 7-segment display to scroll through the letters of his name with a state machine that outputs the desired combination of 1’s and 0’s to the LED display each time the tactile button is pushed.
[Will] uses a 4-bit counter made up of D Flip-Flops for the clock signal as a conditional input to 6 of the 4-input AND gates. He doesn’t go into the painful details of displaying each character through the process (thankfully) but he does mention that he uses the Quine-McCluskey technique for reduction instead of Boolean algebra. Since his name is 11 characters long and the 4-bit binary counter goes from 0000 to 1111 leaving 5 more pushes of the button before rolling the count back to 0000, during which time the display is left blank. [Will] kindly includes the eagle and Gerber files for your downloading pleasure over at his blog if you’re interested in getting a little deeper into the design.
[Will] went with boards 0.8mm thin instead of the standard 1.6mm which affords more thickness for the surface mount parts. The BOM totals: 15 ICs, a coin cell battery, a push button, 7 current limiting resistors, and a capacitor as a hardware debounce. [Will] assembled them himself by hand placing the SMD components and left the soldering to his Reflow Château.
The use of logic gates instead of a micro-controller shows some understanding of logic based design, which is a bit rare when compared to hobbyists with some micro-controller knowledge. Not to say that the PCB business cards that include a micro aren’t impressive in their own right. If you need to brush up your logic chops there are a few recent posts that you might find useful: [Bil Herd’s] logic series, and [Al Williams] covered a browser based logic discussion of flip-flops.
Filed under: classic hacks, lifehacks
World Maker Faire 2015: Prometheus and The New Air Quality Egg
There were plenty of projects and products to be seen at the 2015 World Maker Faire. In the maker pavilion, we found [Rocco Tuccio] showing off Prometheus, his PCB CNC router. Machines like this make prototyping circuits easy. Just place a blank piece of copper clad in the machine, load up your design, and a few minutes later you’ll have a board ready to stuff. Prometheus sports some impressive specs: 7 mil (0.18 mm) trace and space, and a Total Indicated Runout (TIR) of .0001 inches (2.5 micron). Not bad for a spindle turning 40,000 RPM. [Rocco] has spent the last two years designing this machine, and has sourced most of the parts from local US vendors. The unique part of Prometheus is the spindle design. Like many other small PCB routers, Prometheus uses a brushless quadcopter motor for power. Rather than go with a belt system, [Rocco] simplified things to a simple friction drive. The only precision parts he has to worry about are the bearings which hold the cutting bits in place. Prometheus isn’t for sale yet. [Rocco] plans to launch a Kickstarter campaign in the coming months.
A few minutes later we ran into [Victor Aprea] from Wicked Device, showing off the Air Quality Egg V2. [Victor] and his partner [Dirk] ran the design and manufacturing side of the Air Quality Egg, which had a successful Kickstarter campaign back in 2012. The eggs from that campaign can be found online at the project’s website. [Victor and Dirk] have greatly improved on the Egg since then. The biggest update are the sensors. Sensors for ozone, nitrogen dioxide, and sulfur dioxide are now much more sensitive units from SpecSensors. These sensors don’t come cheap though. To keep costs down, [Victor and Dirk] have released three separate versions of the product with different sensor suites. On the connectivity side, the egg is now based upon Wicked Device’s Wildfire, allowing it to connect to WiFi networks. These Eggs mean business too – [Victor and Dirk] obtained permission to co-locate a trio of eggs alongside an official New York State/EPA air quality sensing unit. The Eggs all read within 2 parts per million for carbon monoxide, and 10 parts per billion for sulfur dioxide. As with the original Egg, these devices are open source hardware. Source code is available on Wicked Device’s Github.
Filed under: misc hacks
3D Popup Cards from 3D Photos
The world of 3D printing is growing rapidly. Some might say it’s growing layer by layer. But there was one aspect that [Ken] wanted to improve upon, and that was in the area of 3D photos. Specifically, printing a 3D pop-up-style photograph that collapses to save space so you can easily carry it around.
It’s been possible to take 3D scans of objects and render a 3D print for a while now, but [Ken] wanted something a little more portable. His 3D pop-up photographs are similar to pop-up books for children, in that when the page is unfolded a three-dimensional shape distances itself from the background.
The process works by taking a normal 3D photo. With the help of some software, sets of points that are equidistant from the camera are grouped into layers. From there, they can be printed in the old 2-dimensional fashion and then connected to achieve the 3D effect. Using a Kinect or similar device would allow for any number of layers and ways of using this method. So we’re throwing down the gauntlet — we want to see an arms-race of pop-up photographs. Who will be the one to have the most layers, and who will find a photograph subject that makes the most sense in this medium? Remember how cool those vector-cut topographical maps were? There must be a similarly impressive application for this!
[Ken] isn’t a stranger around these parts. He was previously featured for his unique weather display and his semi-real-life Mario Kart, so be sure to check those out as well.
Filed under: digital cameras hacks, Kinect hacks
Subscribe to:
Posts (Atom)